New connector har-speed M12 (HARTING)
HARTING's new har-speed M12 connector meets the stringent requirements of Category 6A. This is the first time that an M12 cabling system can be used in a high-speed data transmission environment. The new connectors are best suited for high-bandwidth machinery, equipment installation engineering, and other engineering applications where there is an urgent need to provide faster and safer data transmission than Cat. This new development is based on the new PAS 61076 - 2 - 10x standard, which defines a unified docking port for the 8-pin M12 connector. The new docking port has two functions: the docking area of ​​the shielded connector (for paired shielded wires) and the coding of the docking port to ensure successful docking with other 8-pin M12 connectors. Finished cables of various lengths and crimp connectors for field assembly are also being developed to complement this new Yadi product line.
This article refers to the address: http://
Aluminum PCB , it's the PCB that use Aluminum as the base material and very commonly used in LED products and other electronics products since aluminum is the material have high heat dissipation.
PCB = printed circuit board and PCBA = printed circuit board assembly. For PCB, it means the copper circuits be printed on a board, and so the main composition of PCB are copper and board.
The copper is the circuits material and the circuits designed by the PCB designers. Depends on the current in the circuits, the PCB copper thickness could be done with 0.5oz-10oz. But the PCB designers need be noted that the copper track width/space need be enlarged with the thickness. For example, the minimum copper track width/space could be 3mil/3mil with 0.5oz, but would be 4mil/4mil with 1oz.
The PCB board could be rigid PCB, could be flex PCB and also could be Flex-Rigid PCB. And the materials could be FR4, PI, Aluminum, Copper-based, Rogers, Teflon, etc. They have different applications. For example, FR4 PCB is the most commonly used for rigid PCB and almost good for all electronics products; PI is the most commonly used for flex PCB; Aluminum and copper-based have good thermal diffusivity and always used for LED PCB ; Rogers PCB and Teflon PCB are always used for High Frequency PCB, etc.
We are the one-stop shop for all kinds of PCB manufacture service from PCB Prototype to big volume, which could save our customers a lot of time and money.
PCB Manufacture Capabilities
|
Features |
Capabilities |
|
Layers |
1-36 layers |
|
Material |
FR-4, Aluminum, Copper, Polyimide, high frequency (Rogers, PTEE, PI), etc. |
|
PCB Type |
FR-4 Standard PCB , Aluminum PCB, Copper-based PCB, HDI PCB , Rigid-Flex PCB, Flex PCB, Thick Copper PCB and Rogers PCB, etc. |
|
Board Thickness |
0.1mm-6.0mm |
|
Copper Thickness |
1/2oz-6oz(18um-210um) |
|
Biggest Board size |
600mm*1200mm |
|
Min Tracing/Spacing |
0.075mm/0.075mm (3mil/3mil) |
|
Min drilling Hole diameter |
0.15mm(6mil), 0.1mm(4mil)-laser drill |
|
Solder Mask |
Green, Black, White, Red, Yellow, Blue and Purple, etc. |
|
Silkscreen color |
White, Blue, Black, Red, Yellow |
|
Surface finish |
HASL Lead free, Immersion Gold (ENIG), Immersion Tin, Immersion Silver, OSP, Carbon oil, etc. |
|
Special Techniques |
Impedance Control, Gold Fingers, Blind/Buried vias, Peelable solder mask, Half holes, Via-in-Pad and Countersink hole, etc. |
PCB Products Show
PCB Factory Show
Aluminum PCB
Aluminum PCB,Aluminum PCB Prototyping,Aluminum Clad PCB,Aluminum Base PCB
ZhongFeng Electronic Technology Co., Limited , http://www.dopcba.com